Theoryshare - The Broadband Experts

Hi tplewa .
I tested your "product" today  . First write my old flash with bootloader and all memory . When I have recorded old setting i write new firmware and reebot modem. I have opened next administrator panel  . Firmware  is very good on truth  .  There it is a lot useful option . It is of use for particularly telnet and config file ISP who is possible write and edition ( If it is necessary  ).I had some trouble with exclusion BPI but as I have advised ....I have used downgrade BPI + and when I had already BPI - turn off this sheet  and begin acting .Maximum transfer that after editing of tftp server file is 15Mb/sek-download and 2,5Mb/sek -upload. not bad though i have put  30Mb/sek -download and 20Mb/sek -upload .I think my ISP has some global bandwith .
pozdrawiam mam nadzieję że coś ktoś z tego zrozumie he he

Received a UCD for Upstream Channel 4!

Received a UCD for Upstream Channel 1!
Logging event: T501.0 Acquired Downstream (591000000 Hz)........ SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2223898630> T501.0 Acquired Downstre
am (591000000 Hz)........ SUCCESS
0x000537aa ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto:  ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:162, cmty="public"
RNG-RSP  Adj: tim=3954 power=0 freq=0  Stat=Continue
0x00053b92 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ConfigStati
onMaint:  (CmDocsisCtlThread)
        config is kStationMaintenance mode.
RNG-RSP  Adj: tim=0 power=0 freq=0  Stat=Success
0x00053f7a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ConfigStati
onMaint:  (CmDocsisCtlThread)
        config is kPeriodicRanging mode.

******************************************
            UPSTREAM STATUS
******************************************
       Upstream Status = UP
      Upstream Channel = 2
    Upstream Frequency = 24000000 Hz
        Upstream Power = 44 dBmV
           Ranging SID = 0x8e8
  Upstream Symbol Rate = 2560000 sym/sec
******************************************

Starting IP Initialization with DHCP...
DHCPc:  Waiting 4 seconds before sending Discover; client id htype=1, value=00:0
e:5c:1f:91:1e
Logging event: T500.0 Acquired Upstream .......... SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2223898629> T500.0 Acquired Upstream
 .......... SUCCESS
0x00053f84 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto:  ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:162, cmty="public"
CM> DHCPc:  Sending Discover packet; client id htype=1, value=00:0e:5c:1f:91:1e
DHCPc:  Received an Offer from DHCP server 00:13:5f:04:16:05 (73.2.88.1); lease
client id htype=1, value=00:0e:5c:1f:91:1e
CM> DHCPc:  Timed out waiting for offers for lease with client id htype=1, value
=00:0e:5c:1f:91:1e
DHCPc:  Sending Request packet; client id htype=1, value=00:0e:5c:1f:91:1e
DHCPc:  Received an Ack from DHCP server 00:13:5f:04:16:05 (73.2.88.1); lease cl
ient id htype=1, value=00:0e:5c:1f:91:1e
Current IP address is default 169.0.0.1; removing existing route...
0x000557a8 ['DHCP Client Thread' id=0x807c8fa0] BcmVxIpHalIf::ConfigureLeaseImpl
:  (IP Stack1 HalIf)
Configuring IP stack 1:
    IP Address = 73.2.204.44
   Subnet Mask = 255.255.248.0
        Router = 73.2.200.1

DHCP completed successfully!

DHCP Settings:
                     Client Id = htype=1, value=00:0e:5c:1f:91:1e
                         State = Bound (4)
                  Static Lease = false
               AutoConfig Mode = IP, Subnet and Router
                           XID = 0x7557
               Number of Tries = 0
            Max Discover Tries = 6
             Max Request Tries = 6
          DHCP server MAC addr = 00:13:5f:04:16:05
         My offered IP address = 73.2.204.44
               (1) Subnet Mask = 255.255.248.0
         (3) Router IP address = 73.2.200.1
   (54) DHCP Server IP address = 68.87.66.18
   (82) Relay Agent IP address = 73.2.88.1
        TFTP Server IP address = 68.87.66.16
         CM Configuration file = 'd11_walledgarden.cm'
           (2) UTC Time Offset = -21600 seconds
    (4) Time Server IP address = 68.87.66.16
     (7) Log Server IP address = 0.0.0.0
               (51) Lease time = 604142 seconds
               (58) T1 (renew) = 302071 seconds
              (59) T2 (rebind) = 528624 seconds
             Lease is infinite = false


  CmSnmpAgent::IpAddressAcquiredEvent for SB5100 CM Agent
    IP addr = 73.2.204.44
SB5100 CM Agent ConfigIp: Ip=73.2.204.44, Subnet=255.255.248.0, Gateway=73.2.200
.1
CM> Starting Time Of Day...
0x00055b9a ['CmDocsisIpThread' id=0x807c3b50] BcmDocsisTimeOfDayThread::SetTodSe
rverIpAddress:  (Time Of Day Thread) ToD servers:  68.87.66.16
Connecting to ToD server 68.87.66.16...
Sending UDP ToD request to server...
Logging event: D511.0 Retrieved DHCP .......... SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2223898627> D511.0 Retrieved DHCP ..
........ SUCCESS
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:162, cmty="public"
v1Trap: cmTrapLog 73.2.204.44->192.168.100.10:162, cmty="public"
UTC returned by ToD server 3425556539; UTC offset -21600
Current system time -> SUN JUL 20 09:28:59 2008

System start time -> SUN JUL 20 09:23:10 2008

Starting Tftp of configuration file...
Opening file 'd11_walledgarden.cm' on 68.87.66.16...
tftpInit: Tftp outbound interface flag (1024)
Connected to 68.87.66.16 [69]
mode set to octet.
getting from 68.87.66.16:d11_walledgarden.cm [octet]
tftpSend: Attempt #(1) Backoff (2) tickCount (35152) blkReply (1)
CM>  * SB5100MoD Save cmConfig  d11_walledgarden.cm (5436 bytes) to RAM Memory
 * SB5100MoD Downloading cmConfig d11_m_na_c05.cm from TFTP IP: 192.168.100.11
tftpInit: Tftp outbound interface flag (0)
Connected to 192.168.100.11 [69]
mode set to octet.
getting from 192.168.100.11:d11_m_na_c05.cm [octet]
tftpSend: Attempt #(1) Backoff (2) tickCount (35190) blkReply (1)
Tftp read ZERO bytes, may have reached end of file.
Config file was read!  IP Initialization completed...
ERROR:  CoS and/or QoS settings are missing
0x00055eb0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ParseAndVal
idateConfigFile:  (CmDocsisCtlThread) ERROR -
        BcmCmConfig validation tests failed.
0x00055eb0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ConfigFileE
rrorEvent:  (CmDocsisCtlThread) ERROR - Error detected in CM config file.  Downl
oad rescue(!) config file.
0x00055eba ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) ERROR - Failed to read the config file, or it was
rejected by the client!
0x00055eba ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) ERROR - Will try again later...(after 20 seconds).
0x00055eba ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) WARNING -
**
*
* Using non-DOCSIS compliant TFTP retry timeout value from nonvol!
* DOCSIS requires 600 seconds!
*
**

Time Of Day completed...
  BcmSnmpAgent::SystemTimeChangeEvent for SB5100 CM Agent
Logging event: TFTP file complete - but missing mandatory TLV
Sending syslog message from IF 1 to 192.168.100.10:
  <130> CABLEMODEM [DOCSIS]: <68000900> TFTP file complete - but missing mandato
ry TLV File name = d11_walledgarden.cm
Logging event: BcmCmConfig validation tests failed, re-scanning downstream
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2436694036> BcmCmConfig validation t
ests failed, re-scanning downstream
Logging event: D509.0 Retrieved TFTP Config d11_walledgarden.cm SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2223898626> D509.0 Retrieved TFTP Co
nfig d11_walledgarden.cm SUCCESS
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:162, cmty="public"
v1Trap: cmTrapLog 73.2.204.44->192.168.100.10:162, cmty="public"
Logging event: D507.0 Retrieved Time....... SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2223898625> D507.0 Retrieved Time...
.... SUCCESS
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:162, cmty="public"
v1Trap: cmTrapLog 73.2.204.44->192.168.100.10:162, cmty="public"
CM> Starting Tftp of configuration file...
Opening file 'd11_walledgarden.cm' on 68.87.66.16...
tftpInit: Tftp outbound interface flag (1024)
Connected to 68.87.66.16 [69]
mode set to octet.
getting from 68.87.66.16:d11_walledgarden.cm [octet]
tftpSend: Attempt #(1) Backoff (2) tickCount (37202) blkReply (1)
CM>  * SB5100MoD Save cmConfig  d11_walledgarden.cm (5436 bytes) to RAM Memory
 * SB5100MoD Downloading cmConfig d11_m_na_c05.cm from TFTP IP: 192.168.100.11
tftpInit: Tftp outbound interface flag (0)
Connected to 192.168.100.11 [69]
mode set to octet.
getting from 192.168.100.11:d11_m_na_c05.cm [octet]
tftpSend: Attempt #(1) Backoff (2) tickCount (37239) blkReply (1)
Tftp read ZERO bytes, may have reached end of file.
Config file was read!  IP Initialization completed...
ERROR:  CoS and/or QoS settings are missing
0x0005aeba ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ParseAndVal
idateConfigFile:  (CmDocsisCtlThread) ERROR -
        BcmCmConfig validation tests failed.
0x0005aeba ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ConfigFileE
rrorEvent:  (CmDocsisCtlThread) ERROR - Error detected in CM config file.  Downl
oad rescue(!) config file.
0x0005aeba ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) ERROR - Failed to read the config file, or it was
rejected by the client!
0x0005aeba ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) ERROR - Will try again later...(after 20 seconds).
0x0005aeba ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) WARNING -
**
*
* Using non-DOCSIS compliant TFTP retry timeout value from nonvol!
* DOCSIS requires 600 seconds!
*
**

Logging event: TFTP file complete - but missing mandatory TLV
Sending syslog message from IF 1 to 192.168.100.10:
  <130> CABLEMODEM [DOCSIS]: <68000900> TFTP file complete - but missing mandato
ry TLV File name = d11_walledgarden.cm
Logging event: BcmCmConfig validation tests failed, re-scanning downstream
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2436694036> BcmCmConfig validation t
ests failed, re-scanning downstream
Logging event: D509.0 Retrieved TFTP Config d11_walledgarden.cm SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2223898626> D509.0 Retrieved TFTP Co
nfig d11_walledgarden.cm SUCCESS
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:162, cmty="public"
v1Trap: cmTrapLog 73.2.204.44->192.168.100.10:162, cmty="public"
CM> Starting Tftp of configuration file...
Opening file 'd11_walledgarden.cm' on 68.87.66.16...
tftpInit: Tftp outbound interface flag (1024)
Connected to 68.87.66.16 [69]
mode set to octet.
getting from 68.87.66.16:d11_walledgarden.cm [octet]
tftpSend: Attempt #(1) Backoff (2) tickCount (39250) blkReply (1)
CM>  * SB5100MoD Save cmConfig  d11_walledgarden.cm (5436 bytes) to RAM Memory
 * SB5100MoD Downloading cmConfig d11_m_na_c05.cm from TFTP IP: 192.168.100.11
tftpInit: Tftp outbound interface flag (0)
Connected to 192.168.100.11 [69]
mode set to octet.
getting from 192.168.100.11:d11_m_na_c05.cm [octet]
tftpSend: Attempt #(1) Backoff (2) tickCount (39286) blkReply (1)
Tftp read ZERO bytes, may have reached end of file.
Config file was read!  IP Initialization completed...
ERROR:  CoS and/or QoS settings are missing
0x0005feb0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ParseAndVal
idateConfigFile:  (CmDocsisCtlThread) ERROR -
        BcmCmConfig validation tests failed.
0x0005feb0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ConfigFileE
rrorEvent:  (CmDocsisCtlThread) ERROR - Error detected in CM config file.  Downl
oad rescue(!) config file.
0x0005feb0 ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) ERROR - Failed to read the config file, or it was
rejected by the client!
0x0005feb0 ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) ERROR - Will try again later...(after 20 seconds).
0x0005feb0 ['CmDocsisIpThread' id=0x807c3b50] BcmCmDocsisIpThread::RestartTftpCo
nfigFile:  (CmDocsisIpThread) WARNING -
**
*
* Using non-DOCSIS compliant TFTP retry timeout value from nonvol!
* DOCSIS requires 600 seconds!
*
**

Logging event: TFTP file complete - but missing mandatory TLV
Sending syslog message from IF 1 to 192.168.100.10:
  <130> CABLEMODEM [DOCSIS]: <68000900> TFTP file complete - but missing mandato
ry TLV File name = d11_walledgarden.cm
Logging event: BcmCmConfig validation tests failed, re-scanning downstream
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2436694036> BcmCmConfig validation t
ests failed, re-scanning downstream
Logging event: D509.0 Retrieved TFTP Config d11_walledgarden.cm SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
  <134> CABLEMODEM [Motorola Corporation]: <2223898626> D509.0 Retrieved TFTP Co
nfig d11_walledgarden.cm SUCCESS
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:162, cmty="public"
v1Trap: cmTrapLog 73.2.204.44->192.168.100.10:162, cmty="public"
CM>

Extracted from another forum:

This sucks..... Wish someone could help me get online with my sb5100 and comcast etc..  Keep getting CVC configuration file errors and TLV 11 errors. 

HFC Mac and Serial match the
information that is stored in the modem's unique certificates.

I came from an area that had suddenlink and had to change my MAC at the time.  I tried just changing it back, but it still gives cvc errors and what not.  How do I view the modem's certificate to change my MAC to what that is showing?  Thanks!

First many thanks for that great firmware! It's much better than Sigma!!!

A feature I would like to have is to change the BPI2 RSA public key and the BPI2 X509 cable modem certificate.

I can sniff the BPI2 keys without problem, but don't know how to change them easyly... I try to clone the modem, I have everything MACs, Serial no, and the keys.

Again Thanks a lot and keep on with that firmware!

To speed up the cable is no problem as I can easaly sniff other configuration files.

But as I have canceled my cable internet (I don't need the cable internet anymore as I have VDSL (22MBit down/1MB up)), I want to clone my modem with an other MAC...

Feature suggestion:

To be able to force the dhcp server to give the ethernet card the IP you want.
That would allow you to make snmp scans from a certain allowed IP range.

Hi all, this is really just a feature sugestion i'd like to make because although I really like the look and feel of your firmware I believe that this is a feature that will be really useful as I can't get my sb5100 to lock onto the frequency! So my sugestion is to make a frequency up&down feature that you can enter the frequency's manually instead of letting the modem search itself.
I also recon that a ip force feature would be a great idea especially for us in areas that can only use the ip that's given to us by the CC.
Thanks and great work Telpa, keep it coming and I can't wait to see the Final version when it's done with beta testing.